What These Tube Clips Do
Bijur Delimon tube clips hold nylon or copper lubrication tubing against a machine frame. They keep runs tidy and stop vibration against edges.
These clips are fasteners, not fittings. They do not carry any pressure function. For context on system routing, see our guide on what is a central lubrication system.
Official Clip Table
Use the following verified designations to select the correct aftermarket cross-reference clip.
- A2435 for four millimeter tubing, one tube
- B3539 for four millimeter tubing, two tubes
- B7535 for four millimeter tubing, three to five tubes
- 35476 for six millimeter tubing, one tube
- 35011 for eight millimeter tubing, one tube
- B6508 for ten millimeter tubing, one tube
No other tube counts or diameters are listed in the catalog excerpt.
One-Tube Versus Multi-Tube Clips
Single-tube clips like A2435, 35476, 35011, and B6508 secure one line at a clamp point. Multi-tube clips B3539 and B7535 bundle parallel runs into one clamp point.
Multi-tube clips reduce the number of mounting holes on a machine. They work for parallel tube runs only, not crossing lines.
Tubing These Clips Serve
Nylon tubing in the same catalog includes part 5N25 for four millimeter outside diameter and part 35006 for six millimeter outside by four millimeter inside diameter. Copper tubing is cataloged separately with its own clip sizing.
For helical coil nylon pipe options that pair well with these clips, see this helical coil nylon pipe.
Installation Notes
Mount clips with a screw or bolt through the clip body. Each clip clamps around the tube without piercing it.
Because the catalog excerpt does not state clip body material, confirm material at quotation. For connection points, review the Bijur straight connector page.
Ordering
This site supplies aftermarket cross-reference clips. To check stock or request a quotation, request a quotation.
Always verify tube outside diameter and tube count before selecting a part number.
Frequently Asked Questions
What do these clips hold?
They hold nylon or copper lubrication tubing against a machine frame. The clips keep runs tidy and stop vibration against sharp edges.
Are these clips pressure fittings?
No, these clips are fasteners only and carry no pressure function. They position tubing but do not connect or seal any fluid path.
What is the A2435 clip for?
A2435 holds a single four millimeter tube against a machine surface. Use it for simple one-line lubrication runs.
What does B7535 clamp?
B7535 clamps three, four, or five parallel four millimeter tubes. It bundles several lines into one tidy clamp point.
Which clip fits a six millimeter tube?
Part 35476 holds one six millimeter lubrication tube. It suits single-line runs at that diameter.
Do these clips fit copper tubing?
Copper tubing uses the same clip sizes but is cataloged separately. Check the official clip table for your tube diameter.
Is the clip body material stated?
The catalog excerpt does not state the clip body material. Confirm material at quotation before ordering.
What nylon tubing part numbers pair with these clips?
Part 5N25 is four millimeter outside diameter nylon tube. Part 35006 is six millimeter outside by four millimeter inside diameter.
Can one clip hold multiple tube runs?
Yes, B3539 holds two parallel four millimeter tubes, and B7535 holds three to five. Single-tube part numbers like 35476, 35011, and B6508 hold one run each.
Who builds and supports these units?
IsoHiTech Lubrication Systems, founded in 2023, engineering since 2006, builds and supports every unit. Email inquiry@isohitech.com for specifications and a quotation.
For ordering assistance, contact the quotation team.
Bijur Delimon is a trademark of its respective owner.
This page covers aftermarket clips, not manufactured, sponsored, or endorsed by Bijur Delimon.
A2435, B3539, B7535, 35476, 35011, and B6508 are Bijur Delimon designations shown for cross-reference identification only.
