What the 432-24162-1 Does
The Lincoln 432-24162-1 is an aftermarket short straight hose-end stud for reusable three-part KF300 hose ends used in Quicklub centralized lubrication systems. This stud inserts into the hose, then a threaded sleeve slides over the hose and screws onto the stud to compress the hose wall into a seal. Lincoln is a trademark of its respective owner. This is an aftermarket fitting, not manufactured, sponsored, or endorsed by Lincoln. 432-24162-1 designations are for cross-reference identification only.
The stud measures about 21 mm overall and carries a hex SW10 for wrench assembly. It is the straight, short member of a family that also includes longer straight and angled studs. Do not mistake this for a push-in fitting: assembly uses wrenches on the stud hex and threaded sleeve, not hand insertion or release tools.
Specifications
| Part number | 432-24162-1 |
| Type | Hose stud, short, straight |
| Nominal size | 6 mm |
| Hose | KF300 high-pressure hose, 8.6 x 2.3 mm |
| Hex | SW10 |
| Length | About 21 mm |
| Material | Steel, standard chromated finish |
| System pressure | Up to 350 bar when assembled with the matching threaded sleeve on KF300 hose |
How the Three-Part Hose End Works
The reusable KF300 hose end consists of a stud, a threaded sleeve, and the hose itself. First insert the stud into the cut end of the KF300 hose. Then slide the threaded sleeve over the hose and screw it onto the stud. Tighten with wrenches on the stud hex and the sleeve, which compresses the hose wall into the seal between stud and sleeve.
This fitting is reusable if undamaged. Before reassembly, make a fresh square cut on the hose end. The previously compressed section will not reseal reliably, so remove enough hose to present clean, undeformed material to the stud and sleeve.
Matching KF300 Family Parts
| 432-24162-1 | Straight stud, short, about 21 mm. This page describes this part. |
| 432-23067-1 | Straight stud, long, for added reach when the hose routing needs extension. |
| 532-30739-1 | 90 degree stud, short. Routes the hose at a right angle close to the port. See the 90 degree short hose stud. |
| 532-30738-1 | 90 degree stud, long. Corner routing with extended reach. |
| 432-23031-1 | Threaded sleeve, steel. Pairs with the stud to compress the hose wall. See the matching threaded sleeve. |
| 432-23676-1 | Threaded sleeve, stainless, for corrosive settings. Use where steel sleeves would degrade. |
| 226-14091-4 | Quicklinc valve body, reinforced, RVV 6511-6-M10x1, rated 350 bar at its push-in connection. |
For help choosing among these options, see the guide on selecting grease line fittings.
When to Choose the Short Straight Stud
The short straight stud fits compact installations where the hose already routes cleanly into the port without needing extra extension or angle correction. It keeps the hose end close to the valve body or outlet, which saves space in tight installations. Choose the long straight stud when the hose must clear nearby components before entering the port. Choose a 90 degree stud when the hose approaches at a corner; for the short version, use the 532-30739-1 linked in the family table above.
Quicklinc Naming vs This Stud’s Assembly
Quicklinc is Lincoln’s push-in connection system used at valve bodies and outlets. The 226-14091-4 valve body listed above is an example of a Quicklinc port. Some aftermarket listings group the 432-24162-1 stud under the Quicklinc name because it belongs to the same Quicklub system family. That naming refers to the system family, not this stud’s assembly method.
This stud does not use a push-in insertion, clamping ring, or release tool. It assembles with a threaded sleeve that compresses the hose onto the stud. The stud’s system-side port thread is not declared in the available data. Confirm the port thread of your valve body or outlet when ordering.
Frequently Asked Questions
Is this a complete hose fitting or just the stud?
This listing is for the stud only. You must order the threaded sleeve separately to assemble a complete hose end.
What hose does the 432-24162-1 fit?
It fits KF300 high-pressure hose with dimensions 8.6 x 2.3 mm. The stud’s nominal size is 6 mm.
Is this a push-in fitting like Quicklinc ports?
No, this stud uses a threaded sleeve compression joint. Assembly and removal are done with wrenches, not release tools.
Which threaded sleeve matches this stud?
The steel sleeve 432-23031-1 is the standard match. Use stainless sleeve 432-23676-1 in corrosive settings.
What is the difference between the short and long straight stud?
The short stud is about 21 mm overall for compact routing. The long straight stud extends reach where clearance demands more length.
Is there a 90 degree alternative to this stud?
Yes, the 532-30739-1 is the short 90 degree stud. It routes the hose at a right angle near the port.
What does the 350 bar pressure rating mean for this stud?
The rating applies to the assembled hose end with the matching threaded sleeve on KF300 hose. The stud alone has no declared pressure figure.
What is the port thread on the system side of this stud?
The port thread is not declared in the available data. Confirm the thread of your valve body or outlet before ordering.
Can the three-part hose end be reused after disassembly?
Yes, reuse the stud and sleeve if they are undamaged. Always make a fresh square cut on the hose before reassembly.
Who supplies this aftermarket fitting and how do I order?
IsoHiTech Lubrication Systems, founded in 2023, engineering since 2006, builds and supports every unit. Email inquiry@isohitech.com for specifications and a quotation.
You can also request pricing through the contact page. Use this link to reach the quotation form.
