fbpx
  • fs serious lubrication pump
  • fs grease pump used in the wind industrial
  • fs grease pump back view
  • fs serious lubrication pump
  • fs grease pump used in the wind industrial
  • fs grease pump back view

WHY WIND ENERGY NEED LUBRICATION SYSTEM?

The principle of wind power generation is to harness the wind’s force to move the blades, which in turn drives a generator to convert mechanical energy into electrical energy. Most blade wind turbines operate in harsh environments such as mountainous areas or coastal areas. During operation, these turbines must withstand high-intensity mechanical loads, and manual lubrication is challenging, making it difficult to lubricate them on a regular and precise schedule. Proper lubrication is essential to ensure the blades operate normally.Isohitech Lubrication makes lubrication systems for wind turbines that help extend the time between maintenance visits to 8-12 months. The systems are designed to protect components from contaminants and keep them properly lubricated.

THE LUBRICATION SYSTEM OF THE WIND ENERGY

Due to the low-temperature environment in which wind turbines operate, lubricating grease often becomes semi-solid. Therefore, the electric lubrication pump must be capable of delivering lubricant up to 10 meters. The working pressure of the lubrication pump typically ranges from 28 to 35 MPa. The lubrication system used in wind turbines is divided into several subsystems:

1. Generator Bearing Lubrication System
2. Pitch System Bearing and Gear Lubrication System
3. Main Shaft Bearing and Gear Lubrication System
4. Yaw System Bearing and Gear Lubrication System

The pitch system has three bearings, each with approximately 10 to 20 lubrication points, requiring roughly three complete lubrication systems.

The yaw system has only one bearing that needs lubrication, with approximately 20 lubrication points that require oiling. Typically, a lubrication pump with a capacity of 4 kg to 8 kg is chosen for this purpose.

While the main shaft lubrication system has fewer lubrication points, it usually uses larger oil tanks and lubrication pumps.

A typical lubrication system consists of one lubrication pump, several distribution blocks, and an automatic grease replenishment pump.

WIND ENERGY LUBRICATION

lubrication system application
Wind Turbe Application

Wind Turbe Lubrication Component

WIND ENERGY

CENTRAL LUBRICATION SYSTEM

A wind turbine lubrication system from Bijur Delimon can increase the time between turbine maintenance visits to eight to twelve months because wind turbines are located at high altitudes and strong winds. It is tested as a system before shipment, and we have developed a kit to lubricate wind turbines and windmills.

wind energy

WIND ENERGY LUBRICATION APPLICATION

wind energy
1.3 MW WIND TURBINES
600kW wind energy
600kW WIND TURBINES
offshore wind
OFFSHORE WIND TURBINES

There is an essential need for a proactive lubrication maintenance program for wind turbines due to severe environmental factors and structural and mechanical failures. It is essential to maintain the gearbox, generator bearing, open gear, pitch gear, pitch bearing, rotor shaft, yaw bearing, yaw gear, and hydraulic system for a reliable wind turbine.

  1. Friction reduction
  2. Heat dissipation
  3. Wear prevention
  4. Corrosion protection
  5. Efficiency and performance
  6. Noise reduction

GREASE LUBRICATION SYSTEM (3)

How often do wind turbines need to be greased?

Wind turbines do not require greasing in the traditional sense, as mentioned before. However, they do require regular maintenance to ensure optimal performance. The maintenance schedule for a wind turbine typically includes lubrication of specific components, such as the main bearings and pitch bearing systems.

The lubrication schedule for wind turbines depends on various factors, including the turbine model, design, size, and operating conditions. Typically, these schedules are provided by the turbine manufacturer and are tailored to the specific turbine’s requirements.

Main bearing lubrication is particularly critical since these bearings support the weight and rotational forces of the rotor. Grease or specialized lubricants are applied to the main bearings periodically, typically ranging from every six months to several years, based on the manufacturer’s recommendations and the turbine’s operating conditions.

Pitch bearing systems, which control the angle or pitch of the turbine blades, also require lubrication. The frequency of lubrication for these systems varies but can range from once per year to every few years, depending on the specific turbine design and operating conditions.

It is important to note that scheduled maintenance intervals and lubrication requirements may differ between wind turbine models and manufacturers. Therefore, it is recommended to consult the turbine manufacturer’s guidelines or contact their technical support for accurate and up-to-date information regarding lubrication and maintenance practices for a specific wind turbine.

How are wind turbines lubricated?

Wind turbines are typically lubricated using a combination of greases and oils. The lubrication system in a wind turbine is crucial to maintaining the smooth operation of its various components, such as the gearbox, generator, and bearings.

Gearboxes, which are responsible for converting the slow rotational speed of the rotor into the higher rotational speed required by the generator, require proper lubrication to minimize friction and heat generation. Special high-performance gearbox oils are used for this purpose. These oils have excellent thermal stability and can withstand high loads and pressures.

Bearings within the wind turbine are also lubricated to reduce friction and wear. There are different types of bearings used in wind turbines, such as main bearings and pitch bearings. Grease is commonly applied to these bearings as it offers good adhesion and can withstand the high forces and speeds involved.

Lubrication systems in wind turbines are often automated and include pumps, filters, coolers, and sensors to ensure optimal lubrication performance. These systems continuously monitor oil condition and temperature, adjusting lubricant flow rates as needed. Routine maintenance and periodic oil analysis help to ensure that the lubricants are in good condition and that any necessary changes or additions are made.

It’s important to note that advancements in wind turbine technology are continually being made, including improvements in lubrication systems. For instance, some modern wind turbines employ advanced monitoring and control systems that can optimize lubrication based on real-time performance data, resulting in improved efficiency and longer component lifespan.

What kind of lubricants do wind turbines use?

Wind turbines use a variety of lubricants depending on the specific components and requirements. Here are some commonly used lubricants in wind turbines:

1. Gearbox Lubricants: Wind turbine gearboxes require specialized lubricants to handle the high loads, pressures, and temperatures. Synthetic gear oils (such as polyalphaolefins – PAOs) with additives for extreme pressure (EP) and anti-wear (AW) properties are commonly used. These oils offer high thermal stability, good load-carrying capacity, and excellent resistance to oxidation.

2. Bearing Lubricants: Bearings in wind turbines are subjected to high speeds and forces. Greases are typically used for lubricating bearings due to their ability to adhere to surfaces and provide long-lasting lubrication. Lithium complex, calcium sulfonate, and aluminum complex greases are commonly utilized in wind turbine bearings. These greases provide good water resistance and protect against corrosion.

3. Generator Lubricants: The generator in a wind turbine also requires lubrication. Synthetic oils, such as ester-based fluids, are often used in generator applications due to their high thermal stability, good dielectric properties, and compatibility with electrical insulation materials.

4. Hydraulic System Lubricants: Wind turbines also feature hydraulic systems for controlling pitch adjustment, yawing, and other functions. Hydraulic fluids with anti-wear additives and good resistance to oxidation are used in these systems. Common hydraulic fluids used in wind turbines include mineral oil-based fluids and environmentally friendly biodegradable fluids.

It’s important to note that specific lubricant choices may vary depending on wind turbine design, manufacturer recommendations, environmental conditions, and regulations governing the use of certain types of lubricants. Therefore, it is recommended to consult the turbine manufacturer or follow their guidelines for proper lubricant selection and usage.

How much lubricant is in a wind turbine?

The amount of lubricant in a wind turbine can vary depending on its size, design, and specific components. Typically, larger wind turbines have larger lubricant capacities to accommodate the higher loads and operating conditions.

In general, wind turbines contain several reservoirs or sumps to hold lubricants for different components such as the gearbox, generator, and bearings. The lubricant capacity of a wind turbine gearbox can range from several hundred liters to several thousand liters, depending on the turbine’s power rating and design. For example, a typical 3-5 MW wind turbine may have a gearbox with a capacity of around 700-1500 liters.

The bearing lubrication system also requires a certain amount of grease to ensure proper lubrication. Wind turbine pitch and yaw systems may have separate grease reservoirs. The quantity of grease required for these systems can vary depending on the number and size of bearings involved.

It is important to note that wind turbine lubrication systems are designed to ensure adequate lubrication levels and proper distribution throughout the different components. Automated monitoring and control systems are often in place to ensure optimal lubricant levels and to prevent under or over-lubrication.

Specific lubricant quantities and intervals for replenishment or replacement are usually specified by the wind turbine manufacturer and should be followed as part of routine maintenance procedures to ensure reliable and efficient operation.

How are wind turbines maintained?

Maintaining wind turbines involves a combination of regular inspections, preventive maintenance, and corrective maintenance activities. Here are the key aspects of wind turbine maintenance:

1. Inspections: Wind turbines undergo routine visual inspections by trained technicians to identify any signs of wear, damage, or potential issues. These inspections typically include checks on the rotor blades, tower structure, electrical connections, and lubrication systems.

2. Lubrication: As mentioned earlier, lubrication is essential for wind turbine components’ smooth operation. Regular lubricant analysis is performed to monitor the condition of the lubricants, and oil changes or top-ups are done as required. Lubrication system maintenance includes checking filters, pumps, coolers, and sensors to ensure optimal performance.

3. Rotor Blades: The rotor blades need regular inspections and cleaning to remove dirt, debris, and ice buildup. Minor damage, such as small cracks or erosion, can be repaired through composite patching techniques. In case of significant damage, blade replacement may be necessary.

4. Gearbox and Bearings: The gearbox and bearings are critical components that require attention. Vibration analysis and oil sampling are often conducted to detect any early signs of wear or failure. If necessary, gearboxes or bearings can be repaired or replaced.

5. Electrical Systems: The electrical components, including generators, cables, and control systems, are regularly tested and inspected. Loose connections, damaged insulation, or faulty electrical components are repaired or replaced as needed.

6. Tower Maintenance: The tower structure should be regularly inspected for corrosion, structural integrity, and proper grounding. If corrosion or other issues are found, repairs should be conducted promptly.

7. Maintenance Management Systems: Many wind farms utilize computerized maintenance management systems (CMMS) to schedule, track, and manage maintenance activities efficiently. These systems help in planning inspections, tracking maintenance records, managing spare parts inventory, and scheduling preventive maintenance tasks.

8. Weather Monitoring: Wind turbines have advanced weather monitoring systems to track environmental conditions such as wind speeds, temperature, and ice buildup. Weather data helps optimize turbine operation and alerts maintenance crews to potential hazards.

Proper training, adherence to manufacturer guidelines, and compliance with local regulations are essential for effective wind turbine maintenance. Following a well-designed maintenance plan can help improve turbine performance, extend the lifespan of components, and minimize downtime.

How are wind turbines lubricated?

Wind turbines are lubricated through a centralized lubrication system that ensures the proper distribution of lubricants to various components. Here’s a general overview of how wind turbines are lubricated:

1. Lubricant Selection: The first step is selecting the appropriate lubricants for each component of the wind turbine, such as the gearbox, bearings, and generator. These lubricants are chosen based on factors like load capacity, operating temperature, and compatibility with the materials used in the turbine.

2. Lubrication System: Wind turbines typically have a closed-loop lubrication system that consists of storage tanks, pumps, filters, coolers, and distribution lines. The lubricants are stored in dedicated reservoirs and pumped to the components that require lubrication.

3. Gearbox Lubrication: The gearbox is one of the critical components that require lubrication. Gear oils or synthetic lubricants with specific viscosity and additives are used to reduce friction and wear in the gearbox. The lubricant is continuously circulated through the gearbox to ensure proper lubrication of gears, bearings, and other moving parts.

4. Bearing Lubrication: Bearings in wind turbines, including the main bearings and pitch bearings, are also lubricated to minimize friction and maintain smooth operation. Greases or specialized oils with high adhesion properties are used for bearing lubrication. Grease is often applied using automatic lubrication systems or manual greasing techniques.

5. Monitoring and Maintenance: Wind turbine lubrication systems are equipped with sensors and monitoring devices to measure parameters like oil temperature, pressure, and contamination levels. Regular maintenance, including oil analysis, filter replacement, and system inspections, is performed to ensure optimal performance and early detection of any issues.

6. Maintenance Schedule: Wind turbine lubrication is part of a comprehensive maintenance schedule that includes routine checks, preventive maintenance tasks, and scheduled oil changes. The maintenance intervals are determined based on manufacturer recommendations, operating conditions, and the turbine’s specific requirements.

It’s worth noting that lubrication practices may vary depending on the design and model of wind turbines, as well as advancements in turbine technology. Therefore, it is essential to follow the manufacturer’s guidelines and consult experts for specific lubrication requirements of a particular wind turbine model.

Do wind turbines need grease?

No, wind turbines do not require traditional grease for their operation. Unlike many other mechanical systems that rely on lubricants to reduce friction and wear, wind turbines utilize specialized lubricants known as gearbox oil or lubricating fluids specifically formulated for their unique requirements.

The gearbox in a wind turbine is an essential component responsible for converting the low-speed rotation of the blades into higher-speed rotation required by the generator. These gearboxes are designed to withstand high rotational speeds and strong forces generated by wind, but they still require lubrication for optimal performance and longevity.

Gearbox oil or lubricating fluids used in wind turbines are specially designed to withstand the extreme conditions within the gearbox, including high temperatures, pressures, and shear forces. They provide excellent lubrication, viscosity stability, and protection against wear and corrosion.

Regular maintenance and monitoring of the gearbox oil level and quality are crucial to ensure the proper functioning of a wind turbine. This includes periodic oil changes, filtration, and analysis to identify any potential issues or degradation.

So, while wind turbines don’t need grease like traditional mechanical systems, they do rely on specialized lubricants to maintain their efficiency and overall operational integrity.

Send Your Inquiry Today
Quick Quote
Update cookies preferences
Scroll to Top